The Swimsuit Dryer | Installation
Installing Your Swimsuit Dryer
Step-by-step guide for wall-mounted and counter-top units. Questions? We're here to help.
WhatsApp SupportConfirm all three conditions before beginning to avoid delays or damage.
Select the model you have — wall-mounted (Domed Dryer) or counter-top (2nd Generation).
Tools & Materials Required
Wall screws and plugs are supplied. Source the following separately:
Unbox & Remove Transit Bar
Remove the dryer from its packaging. Your wall plate, securing bracket, and instructions are inside the accessory pack. Locate and remove the transit bar from underneath the machine before proceeding. The unit will not operate if this remains in place.
Do not skip — transit bar must come outMeasure & Mark
Mark a point 100 cm from the floor on your chosen wall. Hold the wall plate below this mark and mark the 6 fixing holes. Use a spirit level — the wall plate must be perfectly horizontal.
Drill & Fit the Wall Plate
Drill the 6 marked holes and press in the raw plugs. Align the wall plate and screw it securely. Double-check it is level before tightening fully.
Mount the Dryer & Fit Securing Bracket
Lift the dryer onto the wall plate. Ensure it is flush against the wall with no gaps. Attach the securing bracket to lock it in place.
Connect the Drain Hose
Pull the waste hose down from the dryer. Connect to a P-trap (fitted by a licensed plumber) or extend the hose to route waste water to a drain or bucket.
Connect Power
Fit conduit if required, then connect the 3-core power cable to the fused spur — or simply plug in if your unit has a plug fitted. Switch on the RCD and confirm the transit bar has been removed.
Engage a qualified electrician for wiringTest the Unit
Place a wet swimsuit into the dryer basket, press the lid for up to 10 seconds, and remove. The front logo should illuminate confirming power is live. Cycle completes in under 8 seconds.
Done in under 8 secondsTools & Materials Required
The following tools must be sourced separately — they are not supplied:
Unbox & Remove Transit Bar
Remove the dryer from its packaging. Remove the transit bar from underneath the machine before any installation. Failure to do so will prevent the unit from operating.
Transit bar must be removed firstMeasure & Mark the Countertop
Using your tape measure, ruler, and marker, measure and mark the cutout dimensions on the worktop as stated in the installation document. Measure twice, cut once.
Score & Cut the Opening
Score the worktop along your markings using a multi-cutting tool, then use the jigsaw to complete the cutout. Remove the excess material cleanly.
Drop the Dryer into the Opening
Lower the unit into the countertop cutout. It should sit flush and secure. The 2nd Generation is designed to install seamlessly into cabinet tops, worktops, and similar surfaces.
Connect the Drain Hose
Pull the waste hose down and connect to a P-trap (fitted by a licensed plumber/tradesman) or extend and route the hose to a drain or collection bucket.
Connect Power
Fit conduit if required and connect the 3-core cable to the fused spur, or plug in if a plug is fitted. Turn on the RCD. Verify the transit bar has been removed before switching on.
Engage a qualified electrician for wiringTest the Unit
Place a wet swimsuit in, press the lid for up to 10 seconds, and remove. The front logo should illuminate when power is live. Cycle completes in under 8 seconds.
Done in under 8 secondsIf your Swimsuit Dryer isn't working after installation, check these three causes first.
Transit Bar Not Removed
The transit bar protects the motor during shipping. If not removed, the unit will not spin. Check underneath and remove it before anything else.
RCD / GFCI Not Switched On
The safety switch may not be in the ON position. Locate it and ensure it is switched on. The front logo should illuminate when power is live.
No Power to the RCD
Check that mains power is reaching the RCD/GFCI. If the front logo is not illuminated, there is no live power at the unit. Contact your electrician to check the circuit.
Reference these figures to ensure your facility meets installation requirements.
Need help with your installation?
Our team is ready to assist via WhatsApp or email — Malaysia-wide support.